·          Industrial discharge luminaire generally suitable for mounting heights of greater  than 3.5m.

·          High frequency ballast.

·          Bi-level dimming function.

·          Programmable economy mode.

·          High purity aluminium reflector.

·          Robust steel body and gear tray construction.

·          Multiple fixing arrangements.

·          Hinged lamp and gear tray for easy access.

·          Thermal cut out where required.

·          Lamp: 250W MBI (supplied) or 400W MBI

·          Dims: (HxLxW) 170x600x320mm.

Brush less single phase motor

• Peak power: 720W
• Rated power: 650W
• Speed: 3000rpm
• AC rated voltage: 230V
• AC rated current: 2.8A
• AC frequency: 50Hz.
• Rated power factor: 1.0.
• Overload circuit breaker.
• 4.5 litre fuel tank
• 1 year warranty.
  

Eden is an attractive weatherproof IP65 LED luminarie complete with Maintained emergency mode.

The Eden body is manufactured in white flame retardant ABS with a polycarbonate diffuser. Eden's polycarbonate diffuser incorporates a Fresnel lens, ensuring excellent light distribution.

To aid rapid installation, the Eden is fitted with a hinged gear tray and has side and rear entry points moulded into the base.

Dimensions (Semi-Recess Cut Out): Length 330mm x Width 90mm

The Anglolite features a robust galvanised rear body which recesses fully into the ceiling and only requires a ceiling depth of 90mm. Within the fitting a hinged, removable gear tray facilitates easy fixing and maintenance and a front trim plate with a diffuser ensures a neat and attractive finish.

The opal diffuser is suitable for fitting a self-adhesive legend kit.

A version with 11 watt PLS lamp is available for use as a rectangular downlight mains luminaire.

For industrial applications high specification 2 x 20w

Phantom units have a constant voltage charger with thermal regulation and current limiting circuitry to maximise battery life. The chargers are fitted with thermal, current and short circuit protection devices and a low voltage disconnect circuit to prevent the batteries entering a deep discharge state in the event of prolonged power failure. Batteries are maintenance free, sealed lead acid with a life expectancy of five years under normal conditions. The LED indicates that the charger is functioning and that the battery is connected. If the LED is not lit when mains are healthy, check the battery and lamps.  Mild sheet steel with light grey finish.  Projectors: Plastic housing with plastic lens (IP20 Tungsten version), plastic housing with glass lens (IP65 Tungsten Halogen version).  Batteries: Five year life maintenance-free sealed-lead acid

 Dimensions: IP20 Versions: Length 315mm x Height 310mm x Depth 105mm

                   IP65 Versions: Length 380mm x Height 370mm x Depth 310mm

Compact ultra-slim LED exit sign and can be used in either maintained or non-maintained emergency modes.  Legend panel is edge-lit and the use of three 1 Watt LED's provide a uniform display display and a long life. The Petina is only 30mm deep.  

Flame retardant Polycarbonate

Charger: Constant current with red LED for mains healthy and connected battery

Batteries: 3 x 1.5AH Nickel Cadmium

LED's: 3 x 1 Watt

Viewing Distance 32 Metres

Dimensions: Length 380mm x Width 255mm x Depth 30mm

The LWSS stainless steel range of water heating cylinders provides effective, fast and safe mains-fed hot water around any property. A high quality vessel employing the best in laser welding technology, the LWSS range features high flow rates, energy efficient insulation and an expansion vessel. A high quality vessel employing the best in laser welding technology, the LWSS range features fast flow rates, energy efficient insulation and an expansion vessel to prevent wasted water.

Ideal for apartments needing Mira showers or similiar where the hot water pressure will be low

·          Duplex stainless steel water heating cylinder – for maximum strength and long life

·          Pressure tested to 15 bar

·          Provides effective, fast and safe mains-fed hot water

·          Two long life incoloy, low noise immersion heaters

·          Easy to install with simple step by step installation guide

·          Energy efficient rigid polyurethane foam insulation (CFC/HCFC free)

·          Relief valve operates at 7 bar / 90-95°C

·          3 bar working pressure

·          High flow rates of up to 55 litres per minute

·          Minimum recommended supply of 1.5 bar with flow rate of 25 litres per minute

·          22mm cold feed

·          Wipe clean, corrosion resistant, white coated steel case

·          25 year cylinder guarantee

·          90ltr 750x510mm

Redring Automatic Hand Dryers
Hygiene is an area where warm air dryers score significantly over paper or linen towels. Germ-free warm air is an extremely hygienic drying meduim - with no risk of cross-infection between users. Hand dryers are approved by the Health and Safety Executive as well as the Ministry of Defence for use in commercial and office environments. They are also accepted by the National Health Service resulting in increasingly widespread use in British hospitals.

Automatic Hand Dryer

Loading: 1.5kW - Weight: 1.9kg Motor: 60w

Fan Speed: 2500rpm Air Volume: 120M3/hr

Dimensions: 285mm(h) x 225mm(w) x 125mm(d)

Ideal for food preparation areas

Class 2 insulation, so no need to earth

Infra-red no 'Touch' on/off sensor to prevent cross contamination

* TWO YEAR WARRANTY (UK) ONLY *

The SB2 has been developed to deliver up to 145/154 cups of hot water every hour. Integral sensors and controls provide automatic fill/top up and temperature management.

• 18 Minute heat up time from cold
• 5 litre rapid draw off after initial heat
• 27 litre minimum hourly output
• 0.5 litre recovery per minute
• 3kw power loading. 0.10k/w/hr
• Large non drip tap with brass spindle
• Lomg life incoloy elements
• Self priming
• Boil dry protection
• 1 Year parts and labour warrenty
• Dims. H420mm x W285mm x D260mm
• Finish stainless steel

The KT64 Multifunction Tester makes ‘ease of use’ it’s top priority with such features as:- A single rotary dial to make your test selection. Non trip loop circuits with Anti Trip Technology (ATT). Slim probe with test button as well as a lockdown option on the instrument for the most convenient hands free testing. The complete package is as important as the easy to use functions - the KT64 comes with a lid, convenient neck strap, a soft carry case with additional room to carry other testing tools and the new ‘super robust’ Kewtech G7 test leads (fused and GS38 compliant). All designed to protect the instrument and make testing as easy as possible. The KT64 caters for all the essential testing requirements of BS7671 (16th edition) in Industrial, commercial and domestic (part P) properties.

• Single selector dial .

• Hands free probe

• Easy to use

• No tripping of RCDs during loop impedance tests

• Test button in probe as well as lockdown test button for ‘hands free’ testing

• Easy PFC & PSC measurement without the need to alter test probes

• Additional LED for warning of high voltage output in insulation test mode

• Selectable touch voltage

• Backlit display

• Auto-test for RCD testing with all results shown on one screen, so no scrolling

• Conducts phase to phase loop tests

• End of line calibration certificate included

• Can be used with rechargeable batteries

Voltage Measurement

To save on having to carry an additional voltage detector the KT64 has a dedicated function for voltage detection.

Continuity Measurement

The test current exceeds 200mA as required for BS7671 and range selection is automatic. Continuous testing can be carried out by use of the test button lockdown feature. A selectable buzzer gives instantaneous indication of continuity.

Easy to use lead null facility eliminates the test lead resistance from the results, the nulled value is retained even if the instrument is switched off. Live circuit warnings are given by a

flashing LED, buzzer and indication on the main display.

Insulation Measurement

The KT64 has three selectable voltages, 250V for low voltage systems, 500V and 1000V. An auto-discharge function ensures that circuits are not hazardous after testing. A red LED gives warning of high voltage output during testing and discharging of the circuit. In case of connecting to a live circuit, a live circuit warning is given by flashing LED, buzzer and indication on the display.

Loop Impedance Measurement

A patented (ATT) low current loop impedance test enables high accuracy loop measurements and quick (7s) testing without tripping RCD’s.

A high current alternative is selectable for even higher accuracy and instantaneous results. This option is easily selectable and the subsequent test will default to the low current test, this saves any inadvertent tripping of the RCD. Polarity indication, supply voltage and frequency values are constantly displayed. The KT64 allows for phase to phase loop tests, again with an