GAS PATIO HEATER

NS085
NS085
Larger picture

Ideal for smokers areas. 12KW STAINLESS STEEL PATIO HEATER. 5m square heat radius. Operated with propane gas. Storage area for gas bottle. BS hose and clip on propane regulator. Height 228cm. Dia.88cm. Weather resistant.

Electric Patio Heater

DX63
DX63
Larger picture

Ideal for smokers areas. 

  • 3kW output.
  • Height: 200cm.
  • Dia: 60cm.
  • IPX4.
  • Finish: Stainless steel.

 

Ceramic Heater

DX147
DX147
Larger picture

Ideal for smokers areas. These ceramic encased aluminium elements operate over a longer wavelength with lower temperatures to provide a softer heat without the glow.  Perfect where robust radiant heating is required, these heaters can be mounted inside or outside. 

  • Robust ceramic elements for efficient radiant heating.
  • Can be mounted inside or outside.
  • Silent operation.
  • No visible light output.
  • Adjustable mounting bracket. Fitted guard included to two elements.
  • Choice of vertical or horizontal 2kW models
  • Dimensions vertical H380mm x W442mm.  Horizontal H255mm x W735mm
  • Recommended height 2.0m. Minimum 1.8m

Outdoor Patio Heater

DX146
DX146
Larger picture

Ideal for smokers areas. With a high quality aluminium case and a choice of outputs, these new patio heaters provide long lasting performance perfect for outdoor dining areas or heating for smokers!  With running costs as low as 10p kWh (dependant on tariff) and an optional mounting kit for fixed hanging installation or pole/mast mounting, they are truly flexible.

 

  • High quality aluminium case finished in two-tone silver.
  • 1.3kW Quartz Infra-red model.
  • 2.0kW Quartz halogen model with "gold" lamp for extended performance.
  • Designed and rated for permanent external installations.
  • Instant heat - avoiding the need for expensive pre-heating.
  • 'In-situ' lamp replacement for minimum downtime. Fitted guard included.
  • Optional mounting kit for hanging or pole/mast mounting.
  • Dimensions H160mm x W594mm with two quartz elements.
 

Automatic PIR control

DX148
DX148
Larger picture

 

The ideal solution where occupancy is variable.  The PIR sensor offers even greater energy savings by turning heaters off when no activity is detected within their zone.  Suitable for use with all outdoor patio heaters, they can be installed in external locations with confidence.

  • Compatible with Quartz heating up to 3kW output.
  • Automatically switches the heater on or off, depending on activity
  • Time delay adjustment (10 seconds to 21 minutes).
  • Full 180 degree coverage over 15m if required.
  • Size of detection area can be reduced.
  • IP54 rated for permanent external use.

Mount Kit DX146 Heater

DX149
Optional mounting kit for hanging or pole/mast mounting

Electric Patio Heater - Wall Mounted

NS096
NS096
Larger picture

Ideal for smokers areas. 

  • 1.3kW.
  • Die cast aluminium construction.
  • Stainless steel screw.
  • Highly polished anodised aluminium reflector.
  • Patented glass to allow more heat through.
  • Dims: (HWD) 355x368x157mm.
  • IP54.
  • Finish: Black.

3KW AIR CURTAIN HEATER

LL79
LL79
Larger picture
Wall or ceiling mounted. Adjustable air flow direction. Half or full load. Automatically cuts to half load when selected temperature is attained. Automatic cut-out. Without thermostat. Dims: (HWD) 165mmx528mmx195mm. FINISH: White.

Air Curtain 3kw/4.5kw/6kw 3 Heat settings. Dimplex.

DX45
DX45
Larger picture
3 HEAT SETTING WARM AIR CURTAIN over door or high level, wall or ceiling mounted, optional remote switch. 3 heat settings. Multi directional, powerfull fan heaters providing a warm air barrier to reduce building heat losses through external doors that are frequently opened. Air curtains reduce the overall energy costs in commercial applications and improve comfort in the working environment. The AC3 Range is the popular choice for shops, reception areas, offices, restaurants and light industrial use. Noise level 15.5 Decibels. 3.5KW/4.5KW = HWD 200*605*135MM. 6KW = HWD 200*905*135MM

Plinth Heater 2.4KW

DX81
DX81

BFH24T, BFH24TS and BFH24TB. The BFH range has been designed to fit neatly and unobtrusively into fitted furniture, display units, fascias or false walls. These heaters are ideal for incorporating into plinths of kitchen or bedroom base units or shop display units.

  • Maximum outputs of 2.4Kw with switching for 800w and 1600w outputs with neon indicator
  • Integral controls
  • Fan only option for cool air circulation
  • Integral thermostat with a temperature range of approximately 5 to 30 degrees, lowest setting provides frost protection level
  • W500mm * H120mm * D395mm

Plinth Heater with Remote 2.4KW

DX82
DX82

BFH24RS, BFH24R and BFH24RB with Remote Control. The BFH range has been designed to fit neatly and unobtrusively into fitted furniture, display units, fascias or false walls. These heaters are ideal for incorporating into plinths of kitchen or bedroom base units or shop display units.

  • Maximum outputs of 2.4Kw with switching for 800w and 1600w outputs with neon indicator
  • Integral controls
  • Switch panel remote control wired to heater. Fan switch, Two heat switches and fuse.  2.5 metre 6-core colour coded cable is supplied for connecting the heater to the switch panel
  • Fan only option for cool air circulation
  • Integral thermostat with a temperature range of approximately 5 to 30 degrees, lowest setting provides frost protection level
  • W500mm * H120mm * D395mm

Hydronic Plinth Heater 2.4KW

DX44
DX82

BUH19W, BUH19B, BUH19S. The hydronic BUH range is designed specifically for use on `wet` heating systems. Small and compact, the BUH fits discreetly into the base of kitchens, reception desks, shop counters and even stair risers. The BUH can emit the same heat as a traditional radiator many times its size, but will not occupy valuable wall space. Fan only operation to hot water system. Complete with flexible hoses and isolating valves.

  • Maximum outputs of 2.4Kw with switching for 800w and 1600w outputs with neon indicator
  • Integral controls
  • Fan only option for cool air circulation
  • Integral thermostat with a temperature range of approximately 5 to 30 degrees, lowest setting provides frost protection level
  • W500mm * H120mm * D395mm
  • Includes White, Brown and Stainless Steel Facias

Plinth Fan Heater

DX38
DX38
Larger picture
      • Three heat settings – 800w, 1600w & 2400w
      • Thermostatically controlled
      • Thermal cut out
      • Three facias included – Brown, White & Stainless Steel
      • Four rubber feet – no vibration
      • Easy to install
      • Pre-wired with 1.5 metres of cable
      • Illuminated switches
      • 3 x colour matched screw sets
      • IP20 Rated

Tango Fan Heater Wall 2KW. FX20V

H36
H36
Larger picture

FX20V Downflow with pull Cord Operation. This wall mounted fan heater features an energy saving regulator. Neon Indicator. 2kw maximum output. Energy saving thermostat switches output down to 1kW once the room is warm. IP44 rated. L229mm H242mm D109mm

FX20VL. Adjustable thermostat with no pull cord. Neon indicator. 2kW maximum output (1kW output selectable at installation) IP44 rated. L229mm H242mm D109mm

FX20VE Electronic runback timer. Energy saving timer that automatically switches heater off after a preset time period. Adjustable between 5 and 150 minutes. Pull cord operation. Neon indicator. IP44 rated. L229mm H242mm D109mm

BATHROOM DOWNFLOW WALL HEATER 2KW

H35
H35
Larger picture
      • Suitable for use in the bathroom, en-suites or kitchen area providing fast warm heat.
      • 2.0kW 240v - 50Hz.  2 built-in safety cut-outs
      • Neon indicator to show "On" position
      • Wall Mountable - with bracket which is fitted to heater
      • Streamline low profile design - compact size
      • Colour - White
      • Dimension LxWxH - 220MM x 240MM x 100MM

Radiant Panel Bathroom Heater APL100/150

DX37
DX37
Larger picture
Provides the ultimate in bathroom heating. Combining the benefits of high comfort radiant panel heating with the added convenience of fixed rails for drying and airing towels. Highly accurate electronic thermostatic control. Complete with two fixed towel hangers (Not heated). User selectable confort, background and frost protection settings. Splash proof to IP4 for use in bathrooms and wet areas. Control can be locked. H830mm/1040mm x W440mm x D200mm. Minimum 100mm from ceiling or side walls and 150mm from floor

Daytona Towel Rails DTR Range

DX30
DX30
Larger picture

The Daytona towel rails incorporates patented DryTech technology.  Each towel rail offers outstanding performance with its rapid warm-up and leaves conventional wet/liquid filled towel rails in the cold.  Sleek, elegant, with a gentle curve of the rail.  

 Unique DryTech™ Technology.

Faster warm-up than conventional towel rails.

Provides more heat from a lower output and is therefore more energy efficient.

Entirely liquid free – no leakage, no rusting.

Even heat distribution – no cold spots.

Rapid towel drying.

Compact, slimlline design.

Lightweight for faster, easier installation.

 

 

Radio frequency wall-mounted rotary controller

DX162
DX162A

Comes complete with RF receiver which must be wired to the relevant appliance.  IPx4 Splashproof for use in wet areas.  Wall mounted controller unit fits into a single gang wiring accessory back box.  Can control any ancillary heater up to a loading of 2kW.  Additional receivers can be controlled by a single controller.  Additional receivers sold separately (DX163)

Boost Timer

RF thermostatic control

30 Minute boost button 

 

 Radio frequency wall-mounted LCD programmer 24hr

Offers 24 hour programming

4 programmable time periods, switching heater between On/Off modes.

Programme advance and manual over ride features

30 minute boost button

Thermostatic control

Back lit LCD screen with power save mode

Ideal for providing extra control to towel rails

Programmes saved in memory for 12 hours in the event of a power failure

 

Radio frequency wall-mounted LCD programmer 7 Day

Offers 7 day programming

4 programmable time periods for weekdays and weekends, switching heater between On/Off modes

30 minute boost button

Thermostatic control

Back lit LCD screen with power save mode

Ideal for providing extra control to towel rails

Programmes saved in memory for 12 hours in the event of a power failure Multiple receivers can be controlled by a single controller

 

Wireless Receiver for Heaters using DX162

DX163
DX163

DX163 features

 

Additional receiver for use with RF controllers/programmers (DX162)

Allows an additional ancillary heater Up to 2kW loading to be controlled simultaneously by RF controller / programmer.

TOWEL RADIATOR DIMPLEX - BR150

DX121
DX121
Larger picture

Higher output models provide an ideal combination of room heating with efficient drying of towels and other fabrics. These versatile heaters are supplied ready for electric use, but may also be connected to a water central heating system with the electric element available for use when the boiler is off.


      • Ladder design maximises capacity for hanging damp towels and clothes. 10 rails
      • Chrome or white finish.
      • Wattage: 150w electric.  320w water
      • Size: H665mm x W630mm x D145mm
      • Slim vertical design to maximise use of wall space even in confined areas.
      • No external controls.
      • Built-in over temperature cut-out.
      • Sealed, liquid filled design for maintenance free use.
      • Provided with inlet/outlet plumbing connections - no expensive adapter needed.
      • IPX4 rated for bathroom use. (Zone 2)

TOWEL RADIATOR DIMPLEX - BR200C

DX123
DX121
Larger picture

Higher output models provide an ideal combination of room heating with efficient drying of towels and other fabrics. These versatile heaters are supplied ready for electric use, but may also be connected to a water central heating system with the electric element available for use when the boiler is off.


      • Ladder design maximises capacity for hanging damp towels and clothes. 10 rails
      • Chrome finish.
      • Wattage: 200w electric.  475w water
      • Size: H665mm x W630mm x D145mm
      • Slim vertical design to maximise use of wall space even in confined areas.
      • No external controls.
      • Built-in over temperature cut-out.
      • Sealed, liquid filled design for maintenance free use.
      • Provided with inlet/outlet plumbing connections - no expensive adapter needed.
      • IPX4 rated for bathroom use. (Zone 2)

TOWEL RADIATOR DIMPLEX - BR250

DX124
DX122
Larger picture

Higher output models provide an ideal combination of room heating with efficient drying of towels and other fabrics. These versatile heaters are supplied ready for electric use, but may also be connected to a water central heating system with the electric element available for use when the boiler is off.


      • Ladder design maximises capacity for hanging damp towels and clothes. 10 rails
      • White finish.
      • Wattage: 250w electric. 525w water. 
      • Size: H665mm x W630mm x D145mm
      • Slim vertical design to maximise use of wall space even in confined areas.
      • No external controls.
      • Built-in over temperature cut-out.
      • Sealed, liquid filled design for maintenance free use.
      • Provided with inlet/outlet plumbing connections - no expensive adapter needed.
      • IPX4 rated for bathroom use. (Zone 2)

TOWEL RADIATOR DIMPLEX - BR350C

DX125
DX125
Larger picture

Higher output models provide an ideal combination of room heating with efficient drying of towels and other fabrics. These versatile heaters are supplied ready for electric use, but may also be connected to a water central heating system with the electric element available for use when the boiler is off.


      • Ladder design maximises capacity for hanging damp towels and clothes. 16 rails
      • Chrome finish.
      • Wattage: 350w electric. 750w water.
      • Size: H1003mm x W630mm x D145mm
      • Slim vertical design to maximise use of wall space even in confined areas.
      • No external controls.
      • Built-in over temperature cut-out.
      • Sealed, liquid filled design for maintenance free use.
      • Provided with inlet/outlet plumbing connections - no expensive adapter needed.
      • IPX4 rated for bathroom use. (Zone 2)

TOWEL RADIATOR DIMPLEX - BR400

DX126
DX122
Larger picture

Higher output models provide an ideal combination of room heating with efficient drying of towels and other fabrics. These versatile heaters are supplied ready for electric use, but may also be connected to a water central heating system with the electric element available for use when the boiler is off.


      • Ladder design maximises capacity for hanging damp towels and clothes. 16 rails
      • White finish.
      • Wattage: 400w electric.  840w water. 
      • Size: H1003mm x W630mm x D145mm
      • Slim vertical design to maximise use of wall space even in confined areas.
      • No external controls.
      • Built-in over temperature cut-out.
      • Sealed, liquid filled design for maintenance free use.
      • Provided with inlet/outlet plumbing connections - no expensive adapter needed.
      • IPX4 rated for bathroom use. (Zone 2)

TOWEL RADIATOR DIMPLEX - BR500

DX127
DX122
Larger picture

Higher output models provide an ideal combination of room heating with efficient drying of towels and other fabrics. These versatile heaters are supplied ready for electric use, but may also be connected to a water central heating system with the electric element available for use when the boiler is off.


      • Ladder design maximises capacity for hanging damp towels and clothes. 22 rails
      • White finish.
      • Wattage: 500w Electric. 1050w Water.
      • Size: H1345mm x W630mm x D145mm
      • Slim vertical design to maximise use of wall space even in confined areas.
      • No external controls.
      • Built-in over temperature cut-out.
      • Sealed, liquid filled design for maintenance free use.
      • Provided with inlet/outlet plumbing connections - no expensive adapter needed.
      • IPX4 rated for bathroom use. (Zone 2)